WEBVTT

00:00:00.291 --> 00:00:04.212
Your Video Doorbell Pro requires an
existing wired doorbell setup

00:00:04.546 --> 00:00:09.342
with a mechanical chime and a
transformer rated for 8 to 24 volt AC.

00:00:09.801 --> 00:00:12.220
To set up, you'll need
your Doorbell Pro kit,

00:00:12.303 --> 00:00:14.014
which includes a torx screwdriver.

00:00:14.431 --> 00:00:17.475
You'll also need your own Phillips-head
screwdriver or drill.

00:00:17.851 --> 00:00:20.270
First, start the setup in the SimpliSafe® App.

00:00:20.895 --> 00:00:24.065
Then switch the power off for your
doorbell at the circuit breaker.

00:00:24.441 --> 00:00:27.193
If you have a brick,
stone or stucco surface,

00:00:27.485 --> 00:00:30.613
you'll need to insert the wall anchors
that come with your new doorbell.

00:00:30.905 --> 00:00:33.283
Mark where you want the
anchors to go with a pencil.

00:00:33.491 --> 00:00:39.122
Then drill a pilot hole in the wall with a
3/16th or 4.75 millimeter masonry bit.

00:00:39.456 --> 00:00:42.459
Then insert the doorbell anchors
and gently hammer them in.

00:00:43.001 --> 00:00:46.838
If you do not need to use anchors, just
mark where you want to drill your holes.

00:00:47.172 --> 00:00:51.718
Then remove the cardboard clearance marker
and use the included one inch screws

00:00:51.718 --> 00:00:53.470
to attach the bracket to the wall.

00:00:53.470 --> 00:00:56.890
If you have angled siding or if you
need to turn your Video Doorbell

00:00:56.890 --> 00:01:00.101
up or down 10 degrees,
we have included an angled bracket

00:01:00.435 --> 00:01:03.188
A corner mount is also available
through our help center.

00:01:03.313 --> 00:01:04.773
Once your bracket is installed,

00:01:05.231 --> 00:01:08.777
loosen the terminal screws and connect
the wires to the mounting bracket

00:01:09.027 --> 00:01:12.697
by sliding the exposed wire behind
the washers around either screw.

00:01:12.989 --> 00:01:15.158
Tighten the screws to secure the wires.

00:01:15.492 --> 00:01:17.452
Push your doorbell onto
the mounting bracket,

00:01:17.827 --> 00:01:20.288
sliding it down until
it clicks into place.

00:01:20.622 --> 00:01:22.415
Now return to your power breaker

00:01:22.415 --> 00:01:25.543
and flip the doorbell circuit breaker
into the on position.

00:01:25.877 --> 00:01:27.378
Once you've tested your doorbell

00:01:27.587 --> 00:01:30.924
and can confirm that it's powered
and connected to the chime properly,

00:01:31.424 --> 00:01:36.596
use the included torque screwdriver to install
the security screw at the bottom of the bell.

00:01:36.888 --> 00:01:39.182
This will hold your Video Doorbell in place.

00:01:39.682 --> 00:01:40.934
Finish setup in the app,

00:01:41.142 --> 00:01:44.395
and your Video Doorbell Pro will
be ready to protect your home.